Stainless Steel Chemical Hand Pump

1. Always carefully read, thoroughly understand and follow the pump operating instructions. Use this pump correctly and with care for the purpose for which it is intended. Failure to do may cause damage or personal injury, and will invalidate the warranty. Retain instructions for future reference.

2. Contact your chemical or fluid supplier to check for compatibility with pump prior to installation and operation

3. Prior to use, always carefully and thoroughly read and understand the COSHH / MSDS information contained in the Safety Data Sheet supplied for the chemical which is to be pumped.

4. Wear protective clothing (goggles, face masks, long sleeves, long trousers, gloves, aprons, etc.) as set forth in the COSHH / MSDS Safety Data Sheet when pumping any hazardous chemicals.

5. Certain liquids, pump & containers should be grounded to avoid static electricity, refer to COSHH / MSDS sheets and site RA.

6. Use the pump in a ventilated area.

7. Pump should be washed out before it is used since processing lubricants may contaminate the fluids.

8. Prior to use, inspect your pump thoroughly verifying its proper assembly.

9. If pump is removed from drum, it should be thoroughly rinsed in a liquid that is compatible with both the pump and fluid.

• Product Code: CT
• Suitable For Fuel: Diesel, Gas Oil, Lubricant

1. Check to see if all parts are included.

2. Assemble handle (Ref No. 13-15) to Handle Shaft (Ref No. 12). Align set screw (Ref No. 16) to indent of Shaft (Ref No. 2) and tighten the set screw (Ref No. 16)

3. In order to avoid leakage, please use appropriate sealant to seal three suction pipe (Ref No. 19). Insert the bung adapter (Ref No. 17+18) into suction pipe (Ref No. 19) and thread suction pipe (Ref No. 19) into pump inlet.

4. Insert pump and suction tube assembled with bung adapter into the drum, and then tighten bung adapter thumb screw (Ref No. 18) by hand. Be sure to set pump and suction tube assembly so that the suction tube is at the desired depth in the drum and is not blocked.

1. Ensure pump is securely mounted to the drum and all safety precautions have been observed.

2. Turn the handle in clockwise direction and discharge liquid into appropriate container.

3. Check that there are no leaks.

Warning: The pump will become harder to turn if used with high viscosity liquid (~400cSt), which may shorten the life of the pump.

4. Ensure pump is stored correctly and secured when not in use – refer to site RA.

Tanks:

The delivery of a tank can be confusing as each manufacturer offers a slightly different service and lead time. Please refer to our Delivery Information page.  Standard tank deliveries are "kerbside" which means the tank will be delivered to the kerb only and not positioned further. Should you have specific delivery requirements or restrictions, please contact us to discuss.

Tanks Over 2500L – Articulated Lorry – Customer Offload:

These tanks will be delivered on an articulated vehicle (approximately 16.5m long x 2.6m wide x 3m high) which has no offloading on board, it is the customer's responsibility to offload the tank, which may require a telehandler / forklift.  Curtain sided vehicles are also used, so please note that if there are obstacles or hanging branches on the road to the delivery site etc, the driver may refuse to drive the vehicle to the customer's location due to the possibility of damaging the vehicle. Please let us know if there are any obstructions before delivery, so we can arrange alternative transport.

18 Tonne Tail Lift HGV

This vehicle is the size of the largest bin lorries (for comparison) and is approximately 8.2m long x 2.6m wide x 4m high, often curtain sided so please note that if there are hanging branches etc, these vehicles will not attempt to drive down due to the possibility of damaging the vehicle and so it is recommended that a smaller vehicle is requested. Tanks will be lowered to the ground but not positioned as this is a kerbside delivery.  If a smaller vehicle is required, please email us at sales@fueltankshop.co.uk quoting your order number and name.

HIAB Delivery

HIAB delivery is available but must be requested and there will be an additional cost for this service. If a HIAB delivery is required, please email us at sales@fueltankshop.co.uk quoting your order number and name, and we will come back to you with a price for this service.

Accessories:

Most accessories will be delivered within 1-3 working days (certain products and postcodes may take longer, please check the product page for update to date information). If you require them quicker, we can on occasions offer a next day service (please contact us to discuss). If the item(s) are out of stock, we will advise you of the expected lead time, and you will of course have the opportunity to cancel with a full refund.

Customers may return items within 14 calendar days (as per our Terms & Conditions) - refer to section 7. **

All Items must be returned unused, refunds cannot be issued for used or previously installed items.

Please be aware that returning a tank can be complicated and expensive, so please check that you are ordering the correct item (we suggest checking the dimensions very carefully).

If you wish to return goods, please complete the form on this page to provide further information.

Once your request is approved, a valid Returns Authorisation Number (RAN) will be issued to initiate the returns process along with information on how & where to return your order along with any costs involved.

Please DO NOT return any goods without this authorisation. Goods cannot be accepted without this.

Returns are not accepted at our Minehead Office, please wait until we contact you before returning any goods.

View Fuel Tank Shop return policy now.